31
CANtieCAR / Re: CanTieCar V5 Purchase
« Last post by Oleksandr on April 07, 2023, 12:20:09 »you can try send message to CAN@tieCAR.net
Recent Posts
32
CANtieCAR / CanTieCar V5 Purchase
« Last post by Ducato on April 07, 2023, 03:42:51 »So, I have a early version of CanTieCar, has had a hard life really so now want to update to the latest Hardware.
I see CTC now has version 5 out, So how does one purchase. I really would prefer to purchase direct from the makers.
I see CTC now has version 5 out, So how does one purchase. I really would prefer to purchase direct from the makers.
33
CANtieCAR / CANtieCAR v5.0 Release
« Last post by Oleksandr on March 06, 2023, 18:18:40 »CANtieCAR v5.0 
Hardware
- Powerful CortexM4-core MCU
- Wi-Fi chipset ESP8266EX
- Bluetooth v2.0 + EDR + BLE
- True USB-ready device: CDC, FT232B/R-emulation, FT2232C-emulation, MSD over SD Card
- SD Card: internal Flash storage with USB-MSD up to 32GB
- 3 independent ISO9141/ISO14239 K-Lines (ISO-Lines): OBDII-pins 7,8,15
- 2 multi-functional lines (MFLs): CAN - one and two-wires, K Lines, J1850, DC-DC-out (5-30V)/1W etc.
- 3 CAN channels at the same time: Dual Wire CAN, Fault-tolerant CAN, Single wire CAN
- SAE J1850 Normal and High Speed support: J1850PWM 41.6 Kbps and 83.3 Kbps; J1850VPW 10.4 Kbps and 41.6 Kbps
- built-in analog switches multiplexer for OBDII-pins 1,2,3,6,8,13 and 8,9,10,11,12,14 with cross-link for the MFLs
- built-in hardware UART multiplexer
- built-in switchable CAN-bus differential terminator 120 Ohm
- 9 Leds: 6 - Bus Activity, 1 bi-color - USB/Bluetooth/Wi-Fi TX Activity + Status, 1 bi-color - Power state: USB and car + USB Activity, 1 bi-color - Bluetooth/Wi-Fi Status/Activity
- 2 DC-DC: 5V/500mA and programmable (5-35V)/1W
- 8 ADC Channels: Power ISO-Lines, Power MFL, High MFL, Low MFL, OBD:1, OBD:8, OBD:9, OBD:16
- Systems: Up to 35V
- Speed: ISO-Lines up to 1Mbit/s; CAN up to 1Mbit/s
- Special OBDII-connector design
- Security Firmware updates
- ALL protections with Resetable fuses
PassThru SAE J2534-1/2 Support
- J1850VPW, J1850VPW_PS
- J1850PWM, J1850PWM_PS
- ISO9141, ISO9141_PS
- ISO14230, ISO14230_PS
- CAN, CAN_PS
- ISO15765, ISO15765_PS
- SW_CAN_PS, SW_ISO15765_PS
- FT_CAN_PS, FT_ISO15765_PS
- UART_ECHO_BYTE_PS
- HONDA_DIAGH_PS
- UBP_PS (UBP - Ford UART Based Protocol)
Emulated well-known adapters
- ECU-Emulator
- PassThru SAE J2534-1/2
- PassThru SAE J2534-1/2 - BMW up to 2008
- PassThru SAE J2534-1/2 - NISSAN Consult-III plus
- MultiECUScan (FiatECUScan v3.4+)
- ELM327 v1.4+
- ELM327 v1.4+ (ScanTool.net)
- USB-Serial (4/5:GND, 6:CTS, 7:RXD, 8:DTR/DSR, 14:RTS, 15:TXD)
- USB-Serial Inverted (4/5:GND, 6:~CTS, 7:~RXD, 8:~DTR/~DSR, 14:~RTS, 15:~TXD)
- K-Line + USB-Serial LPG/CNG (4/5:GND, 12:RX/L, 13:TX/K, 7:K)
- KL-Line (7:K, 15:L)
- 2K-Line (7:K, 15:K2)
- KKL-Line (7:K, 15:L/K2)
- 3K-Line (7:K, 15:K2, 8:K3)
- OPEL 4K-Line (7:K, 8:K3, 3:K4, 12:K5)
- Multiplexed K-Line to ALL OBD-pins
- VAGCOM v409-1 (KKL-Design)
- RS485 Duplex (12:A, 13:B)
- RS485 Half-Duplex (12:A, 13:B)
- Carsoft BMW 6.5/7.3
- Carsoft MB 7.4
- Carsoft MB 7.4 - OBDII
- NISSAN Consult I + Sync (10:TX, 2:RX, 7:SYNC)
- NISSAN Consult I - OBDII (12:TX, 13:RX)
- DIESEL-kit v1.0
- DIESEL-kit v2.0
- P.A.Soft BMW Scanner v1.2.5
- P.A.Soft BMW Scanner v1.3.6
- P.A.Soft BMW Scanner v1.4.0 Demo
- P.A.Soft BMW Scanner v1.4.x
- BMW EDIABAS: STD:OBD
- BMW EDIABAS: ADS
- BMW EDIABAS: D-CAN Combo (STD:OBD K + D-CAN)
- BMW EDIABAS: D-CAN Fast (STD:OBD D-CAN)
- BMW EDIABAS: D-CAN Fxx (STD:OBD D-CAN for F-series)
- BMW EDIABAS: JBE PT-CAN (STD:OBD + JBE CAN 500k)
- BMW EDIABAS: JBE K-CAN (STD:OBD + JBE CAN 100k)
- BMW EDIABAS: FEM x-CAN 6/14 (STD:OBD + FEM CAN 500k)
- CMD EDC16 OBDII Flasher v1255 - K-Line
- CMD MPC5xx BDM Programmer v1255 (4/5:GND-6, 6:RST-1, 7:DI-7, 8:SCK-5, 14:IGN-2, 15:DO-8, 16:PWR-9)
- Galletto v1050/1080 EOBDII Flasher
- Galletto v1245 EOBDII Flasher
- Galletto v1250 EOBDII Flasher
- Galletto v1260 EOBDII Flasher
- VAG K+CAN Commander v1.4/v2.5/v3.6
- Lawicel CAN232 v3 (6:High, 14:Low)
- Lawicel CANUSB v1 (6:High, 14:Low)
- PonyProg2000 (4/5:GND-10, 6:IN#-6, 7:OUT#-5, 8:SCLK#-4, 14:VCC/RST-1/3, 15:RST#-2)
- EDiTH Eberspacher ISO Adapter
- OpenPort v1
- OpenPort v1.2
- OpenPort v1.3 Universal (11:Vpp/Boot)
- USB-Bluetooth Gate - HC-06
- USB-WiFi Gate - ESP8266EX
- USB-WIRELESS Gate - SYSTEM.INI
Status
Production (available from stock)
Support:
e-mail: support@tiecar.net
downloads: http://www.tiecar.net/support.html#CANtieCAR5
Hardware
- Powerful CortexM4-core MCU
- Wi-Fi chipset ESP8266EX
- Bluetooth v2.0 + EDR + BLE
- True USB-ready device: CDC, FT232B/R-emulation, FT2232C-emulation, MSD over SD Card
- SD Card: internal Flash storage with USB-MSD up to 32GB
- 3 independent ISO9141/ISO14239 K-Lines (ISO-Lines): OBDII-pins 7,8,15
- 2 multi-functional lines (MFLs): CAN - one and two-wires, K Lines, J1850, DC-DC-out (5-30V)/1W etc.
- 3 CAN channels at the same time: Dual Wire CAN, Fault-tolerant CAN, Single wire CAN
- SAE J1850 Normal and High Speed support: J1850PWM 41.6 Kbps and 83.3 Kbps; J1850VPW 10.4 Kbps and 41.6 Kbps
- built-in analog switches multiplexer for OBDII-pins 1,2,3,6,8,13 and 8,9,10,11,12,14 with cross-link for the MFLs
- built-in hardware UART multiplexer
- built-in switchable CAN-bus differential terminator 120 Ohm
- 9 Leds: 6 - Bus Activity, 1 bi-color - USB/Bluetooth/Wi-Fi TX Activity + Status, 1 bi-color - Power state: USB and car + USB Activity, 1 bi-color - Bluetooth/Wi-Fi Status/Activity
- 2 DC-DC: 5V/500mA and programmable (5-35V)/1W
- 8 ADC Channels: Power ISO-Lines, Power MFL, High MFL, Low MFL, OBD:1, OBD:8, OBD:9, OBD:16
- Systems: Up to 35V
- Speed: ISO-Lines up to 1Mbit/s; CAN up to 1Mbit/s
- Special OBDII-connector design
- Security Firmware updates
- ALL protections with Resetable fuses
PassThru SAE J2534-1/2 Support
- J1850VPW, J1850VPW_PS
- J1850PWM, J1850PWM_PS
- ISO9141, ISO9141_PS
- ISO14230, ISO14230_PS
- CAN, CAN_PS
- ISO15765, ISO15765_PS
- SW_CAN_PS, SW_ISO15765_PS
- FT_CAN_PS, FT_ISO15765_PS
- UART_ECHO_BYTE_PS
- HONDA_DIAGH_PS
- UBP_PS (UBP - Ford UART Based Protocol)
Emulated well-known adapters
- ECU-Emulator
- PassThru SAE J2534-1/2
- PassThru SAE J2534-1/2 - BMW up to 2008
- PassThru SAE J2534-1/2 - NISSAN Consult-III plus
- MultiECUScan (FiatECUScan v3.4+)
- ELM327 v1.4+
- ELM327 v1.4+ (ScanTool.net)
- USB-Serial (4/5:GND, 6:CTS, 7:RXD, 8:DTR/DSR, 14:RTS, 15:TXD)
- USB-Serial Inverted (4/5:GND, 6:~CTS, 7:~RXD, 8:~DTR/~DSR, 14:~RTS, 15:~TXD)
- K-Line + USB-Serial LPG/CNG (4/5:GND, 12:RX/L, 13:TX/K, 7:K)
- KL-Line (7:K, 15:L)
- 2K-Line (7:K, 15:K2)
- KKL-Line (7:K, 15:L/K2)
- 3K-Line (7:K, 15:K2, 8:K3)
- OPEL 4K-Line (7:K, 8:K3, 3:K4, 12:K5)
- Multiplexed K-Line to ALL OBD-pins
- VAGCOM v409-1 (KKL-Design)
- RS485 Duplex (12:A, 13:B)
- RS485 Half-Duplex (12:A, 13:B)
- Carsoft BMW 6.5/7.3
- Carsoft MB 7.4
- Carsoft MB 7.4 - OBDII
- NISSAN Consult I + Sync (10:TX, 2:RX, 7:SYNC)
- NISSAN Consult I - OBDII (12:TX, 13:RX)
- DIESEL-kit v1.0
- DIESEL-kit v2.0
- P.A.Soft BMW Scanner v1.2.5
- P.A.Soft BMW Scanner v1.3.6
- P.A.Soft BMW Scanner v1.4.0 Demo
- P.A.Soft BMW Scanner v1.4.x
- BMW EDIABAS: STD:OBD
- BMW EDIABAS: ADS
- BMW EDIABAS: D-CAN Combo (STD:OBD K + D-CAN)
- BMW EDIABAS: D-CAN Fast (STD:OBD D-CAN)
- BMW EDIABAS: D-CAN Fxx (STD:OBD D-CAN for F-series)
- BMW EDIABAS: JBE PT-CAN (STD:OBD + JBE CAN 500k)
- BMW EDIABAS: JBE K-CAN (STD:OBD + JBE CAN 100k)
- BMW EDIABAS: FEM x-CAN 6/14 (STD:OBD + FEM CAN 500k)
- CMD EDC16 OBDII Flasher v1255 - K-Line
- CMD MPC5xx BDM Programmer v1255 (4/5:GND-6, 6:RST-1, 7:DI-7, 8:SCK-5, 14:IGN-2, 15:DO-8, 16:PWR-9)
- Galletto v1050/1080 EOBDII Flasher
- Galletto v1245 EOBDII Flasher
- Galletto v1250 EOBDII Flasher
- Galletto v1260 EOBDII Flasher
- VAG K+CAN Commander v1.4/v2.5/v3.6
- Lawicel CAN232 v3 (6:High, 14:Low)
- Lawicel CANUSB v1 (6:High, 14:Low)
- PonyProg2000 (4/5:GND-10, 6:IN#-6, 7:OUT#-5, 8:SCLK#-4, 14:VCC/RST-1/3, 15:RST#-2)
- EDiTH Eberspacher ISO Adapter
- OpenPort v1
- OpenPort v1.2
- OpenPort v1.3 Universal (11:Vpp/Boot)
- USB-Bluetooth Gate - HC-06
- USB-WiFi Gate - ESP8266EX
- USB-WIRELESS Gate - SYSTEM.INI
Status
Production (available from stock)
Support:
e-mail: support@tiecar.net
downloads: http://www.tiecar.net/support.html#CANtieCAR5
34
CANtieCAR / Re: Nissan / Infiniti
« Last post by Oleksandr on February 27, 2023, 12:10:40 »try the some old version Consult III+
35
CANtieCAR / Nissan / Infiniti
« Last post by ViktorsS on February 24, 2023, 18:48:42 »Hi,
Are tieCAR usable for Infiniti?
Are tieCAR usable for Infiniti?
36
CANtieCAR / Re: 2.08.14 drivers does not work with CANtieCAR 4.5
« Last post by tapi0 on October 18, 2022, 21:58:44 »Quote
Try hardware reset to Loobback – press service button before usb connect and hold if until windows would found the deviceThis helped to get my CantieCar 4.5 to work and I'm able to use Multiecuscan now.
- http://tiecar.net/downloads/CANtieCAR_v2x_Service_Flow.pdf
Regards, tieCAR.net Company ::.
So thank you!
37
CANtieCAR / Re: 2.08.14 drivers does not work with CANtieCAR 4.5
« Last post by Highland on October 06, 2022, 10:54:45 »Mine still doesn't work, when i try updating the drivers. Windows saids it already have the best driver installed.
Can anyone help?
Can anyone help?
38
CANtieCAR / Re: 2.08.14 drivers does not work with CANtieCAR 4.5
« Last post by Oleksandr on September 30, 2022, 21:15:56 »CANtieCAR use different drivers because it is emulated different usb-devices
read here
- http://tiecar.net/downloads/CANtieCAR_First_Time_Drivers_Installation.pdf
- http://tiecar.net/downloads/CANtieCAR_v2x_Service_Flow.pdf
read here
- http://tiecar.net/downloads/CANtieCAR_First_Time_Drivers_Installation.pdf
- http://tiecar.net/downloads/CANtieCAR_v2x_Service_Flow.pdf
39
CANtieCAR / Re: 2.08.14 drivers does not work with CANtieCAR 4.5
« Last post by tapi0 on September 13, 2022, 23:43:11 »Well the drivers on built-in storage are v.2.08.14 at this case.
Those drivers are made in 2011 and supposed to be newest ones.
Those drivers are made in 2011 and supposed to be newest ones.
40
CANtieCAR / Re: 2.08.14 drivers does not work with CANtieCAR 4.5
« Last post by pupu14 on September 13, 2022, 19:38:09 »Hello,
Use drivers which are stored on your device built-in storage (SD card).
Or move "CompositeCDCSerial_64.inf" from folder CDC to tieCAR.net, if you let Windows install drivers from that folder only
Use drivers which are stored on your device built-in storage (SD card).
Or move "CompositeCDCSerial_64.inf" from folder CDC to tieCAR.net, if you let Windows install drivers from that folder only