Recent Posts

Pages: 1 ... 3 4 [5] 6 7 ... 10
41
CANtieCAR / 2.08.14 drivers does not work with CANtieCAR 4.5
« Last post by tapi0 on September 13, 2022, 04:34:37 »
I tried to install drivers for my new CANtieCAR 4.5 and it does not found any drivers for it.
I looked up inside of the tcnbus.inf and ftdibus.inf: there is no DeviceDesc for my CANtieCAR device.

I manually edited those two to add proper DeviceDesc and device id's and got those work.
But then it wants driver for USB Serial Port too and I think that driver is tcnport.inf which does not have correct DeviceDesc and device id nether.

I put those in there also but it still does not work.

I'm trying to install this for Win XP but that should not matter.
42
CANtieCAR / Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Last post by Oleksandr on August 20, 2022, 10:47:05 »
perhaps that is wiTech
43
CANtieCAR / Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Last post by ViktorsS on May 22, 2022, 07:27:11 »
What is the best diagnostic and car configuring software for chrysler, for using on pc?
44
CANtieCAR / Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Last post by Oleksandr on April 25, 2022, 15:14:06 »
we have not enough cars for SAE J1850VPW testings...
so the protocol is not ready
45
CANtieCAR / ELM327 mode - can't connect to 2007 Chrysler & Country
« Last post by dbh97 on February 22, 2022, 23:52:48 »
My CANtieCAR won't connect to my 2007 Chrysler Town & Country in ELM327 mode. I'm using the "Car Scanner" Android app.
I believe the Town & Country uses J1850 VPW. I can connect to my 1997 F150 just fine, which uses J1850 PWM.
A cheap handheld OBD reader connects to my Town & Country without any issues.
46
CANtieCAR / Re: V4 getting hot after 5-6 minutes
« Last post by sparky001 on November 04, 2021, 07:11:07 »
Hi,
 Yes received. I'm having issues with current hosting provider for domain & Email. Have just swapped today. So hopefully can buy soon.

Thanks
47
CANtieCAR / Re: V4 getting hot after 5-6 minutes
« Last post by Oleksandr on October 17, 2021, 20:44:40 »
answered to you couple times... recheck spam-filters please.
48
CANtieCAR / Re: V4 getting hot after 5-6 minutes
« Last post by sparky001 on October 03, 2021, 21:52:52 »
Hello mate,
 I hope you are well. I have sent E-Mail twice. everything OK??

Cheers
49
CANtieCAR / CANtieCAR v4.5 Description
« Last post by Oleksandr on May 07, 2021, 21:57:58 »
CANtieCAR v4.5


Hardware
- Powerful ARM-core MCU
- Wi-Fi chipset ESP8266EX
- Bluetooth v2.0 + EDR
- True USB-ready device: CDC, FT232B/R-emulation, FT2232C-emulation, MSD over SD Card
- SD Card: internal Flash storage with USB-MSD up to 32GB
- 3 independent ISO9141/ISO14239 K-Lines (ISO-Lines): OBDII-pins 7,8,15
- 2 multi-functional lines (MFLs): CAN - one and two-wires, K Lines, J1850, DC-DC-out (5-30V)/1W etc.
- 3 CAN channels at the same time: Dual Wire CAN, Fault-tolerant CAN, Single wire CAN
- built-in analog switches multiplexer for OBDII-pins 1,2,3,6,8,13 and 8,9,10,11,12,14 with cross-link for the MFLs
- built-in hardware UART multiplexer
- built-in switchable CAN-bus differential terminator 120 Ohm
- 9 Leds: 6 - Bus Activity, 1 bi-color - USB/Bluetooth/Wi-Fi TX Activity + Status, 1 bi-color - Power state: USB and car + USB Activity, 1 bi-color - Bluetooth/Wi-Fi Status/Activity
- 2 DC-DC: 5V/500mA and programmable (5-35V)/1W
- 8 ADC Channels: Power ISO-Lines, Power MFL, High MFL, Low MFL, OBD:1, OBD:8, OBD:9, OBD:16
- Systems: Up to 35V
- Speed: ISO-Lines up to 1Mbit/s; CAN up to 1Mbit/s
- Special OBDII-connector design
- Security Firmware updates
- ALL protections with Resetable fuses

Emulated well-known adapters
- USB-Serial (4/5:GND, 6:CTS, 7:RXD, 8:DTR/DSR, 14:RTS, 15:TXD)
- USB-Serial Inverted (4/5:GND, 6:~CTS, 7:~RXD, 8:~DTR/~DSR, 14:~RTS, 15:~TXD)
- K-Line + USB-Serial LPG/CNG (4/5:GND, 12:RX/L, 13:TX/K, 7:K)
- KL-Line (7:K, 15:L)
- 2K-Line (7:K, 15:K2)
- KKL-Line (7:K, 15:L/K2)
- 3K-Line (7:K, 15:K2, 8:K3)
- OPEL 4K-Line (7:K, 8:K3, 3:K4, 12:K5)
- Multiplexed K-Line to ALL OBD-pins
- VAGCOM v409-1 (KKL-Design)
- RS485 Duplex (12:A, 13:B)
- RS485 Half-Duplex (12:A, 13:B)
- Carsoft BMW 6.5/7.3
- Carsoft MB 7.4
- Carsoft MB 7.4 - OBDII
- NISSAN Consult I + Sync (10:TX, 2:RX, 7:SYNC)
- NISSAN Consult I - OBDII (12:TX, 13:RX)
- DIESEL-kit v1.0
- DIESEL-kit v2.0
- P.A.Soft BMW Scanner v1.2.5
- P.A.Soft BMW Scanner v1.3.6
- P.A.Soft BMW Scanner v1.4.0 Demo
- P.A.Soft BMW Scanner v1.4.x
- BMW EDIABAS: STD:OBD
- BMW EDIABAS: ADS
- BMW EDIABAS: D-CAN Combo (STD:OBD K + D-CAN)
- BMW EDIABAS: D-CAN Fast (STD:OBD D-CAN)
- BMW EDIABAS: D-CAN Fxx (STD:OBD D-CAN for F-series)
- BMW EDIABAS: JBE PT-CAN (STD:OBD + JBE CAN 500k)
- BMW EDIABAS: JBE K-CAN (STD:OBD + JBE CAN 100k)
- BMW EDIABAS: FEM x-CAN 6/14 (STD:OBD + FEM CAN 500k)
- ELM323 v2.0+
- ELM327 v1.4+
- ELM327 v1.4+ (ScanTool.net)
- CMD EDC16 OBDII Flasher v1255 - K-Line
- CMD MPC5xx BDM Programmer v1255 (4/5:GND-6, 6:RST-1, 7:DI-7, 8:SCK-5, 14:IGN-2, 15:DO-8, 16:PWR-9)
- Galletto v1050/1080 EOBDII Flasher
- Galletto v1245 EOBDII Flasher
- Galletto v1250 EOBDII Flasher
- Galletto v1260 EOBDII Flasher
- VAG K+CAN Commander v1.4/v2.5/v3.6
- Lawicel CAN232 v3 (6:High, 14:Low)
- Lawicel CANUSB v1 (6:High, 14:Low)
- PonyProg2000 (4/5:GND-10, 6:IN#-6, 7:OUT#-5, 8:SCLK#-4, 14:VCC/RST-1/3, 15:RST#-2)
- EDiTH Eberspacher ISO Adapter
- OpenPort v1
- OpenPort v1.2
- OpenPort v1.3 Universal (11:Vpp/Boot)
- MultiECUScan
- PassThru SAE J2534-1/2
- PassThru SAE J2534-1/2 - BMW up to 2008
- PassThru SAE J2534-1/2 - NISSAN Consult-III plus
- ECU-Emulator
- USB-Bluetooth Gate - HC-06
- USB-WiFi Gate - ESP8266EX
- USB-WIRELESS Gate - SYSTEM.INI

Status
Discontinued (available from stock)

Support:
e-mail: support@tiecar.net
downloads: http://www.tiecar.net/support.html#CANtieCAR4

Pictures (v4.5):








Inside (v4.5):










50
CANtieCAR / Re: Siemens MY99 Airbag - can't connect
« Last post by pupu14 on May 02, 2021, 17:42:06 »
It states on their website (supported vehicles / modules) that this particular Siemens ECU (Siemens Airbag MY99 |INFO|DTC|PRM|ACT| KL A2 P3) is only accessed by "KL - KKL/VagCom/OBDKey interface".
Try changing the mode of Cantiecar dongle to KKL or Vagcom and try it again (don't forget to change adapter setting inside Multiecuscan).
Pages: 1 ... 3 4 [5] 6 7 ... 10