Products Support > CANtieCAR
V4 getting hot after 5-6 minutes
sparky001:
Yes,
Would be better to send back *)
Have found the wires - You must have really good eye sight :o
Will get new cap today & try when I get home
Thanks
Oleksandr:
good luck
sparky001:
Ok,
Working again. Not getting as hot and still communicating after 20+ minutes
Thanks ;D
sparky001:
Works with Forscan - ok
Seems to want top work with JLR V160 - ok
Doesn't work with Xentry anymore
CR:Copyright (C) 2005-2020 tieCAR.net Company ::.
ID:CANtieCAR:tieCAR.net Company ::.
SN:WTCWAK32
BW:4.2.470
HW:4.1
FW:4.1.880
PT:2.6.1204
PW:ON
UP:02
UB:0.354V
PI:ON
UI:4.892V
U8:0.000V
PA:5V
UA:0.567V
Selected Mode: PT0 - PassThru SAE J2534-1/2 (CAN-Terminator:AUTO)
--------------------------------
MCU:AT91SAM7X512
Test MCU pins:..........
14(A09) - Shorted to 60(A26)
.
18(A10) - Shorted to 60(A26)
.
19(A11) - Unconnected
...............
60(A26) - External Pull-Down
...
75(A29) - Shorted to 60(A26)
.
80(A30) - Shorted to 60(A26)
....
43(B03) - Shorted to 60(A26)
.....
28(B08) - Shorted to 60(A26)
.
27(B09) - Shorted to 60(A26)
....
30(B13) - Shorted to 60(A26)
.
29(B14) - Shorted to 60(A26)
..............
10(B28) - Shorted to 60(A26)
.. = ERRORs: 12
--------------------------------
Rates:
K : 1413 kbit/s
L : 1417 kbit/s
K8 : 1417 kbit/s
K-High : ERROR - IO shorted to GROUND
K-Low : 170 kbit/s
CAN : 892 kbit/s
FT_CAN : 153 kbit/s
H-High : ERROR - IO shorted to GROUND
H-Low : ERROR - IO shorted to GROUND
SW_CAN : ERROR - IO shorted to POWER
--------------------------------
Bluetooth: ....................230400:..........OK:..........OKlinvorV1.8 = Present
--------------------------------
WiFi: ..:.1000000:.ESP8266EX 26MHz 512KB 18:FE:34:97:F7:0B = Present
--------------------------------
ADC and POWER Switches:
U_01 : 0.000V - ERROR
U_08 : 0.000V - TEST: 4.821V
U_09 : 0.000V - ERROR
U_16 : 0.248V
--------------------------------
SW_ISO SW_ADJ : U_ISO U_ADJ U_LOW U_HIGH
OFF OFF : 4.892 0.567 0.532 0.532
ON OFF : 4.892 0.567 0.532 0.532
OFF ON : 4.892 0.567 0.532 0.567
ON ON : 4.892 0.567 0.532 0.532
--------------------------------
DC-DC:
Skiped - Apply External Power to device and run test again
RESULT : Error
Any ideas??
Oleksandr:
look a like hard broken
recheck all transitors in sot-23 package marked as 6C and 5C and diodes WW1
there is couple of them with crack holes due to breakage
look on ICs MAX4664 for the same damages
one of them can be hot because it is broken
really there are many damages can caused the errors...
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version