Author Topic: ELM327 mode - can't connect to 2007 Chrysler & Country  (Read 3831 times)

dbh97

  • Newbie
  • *
  • Posts: 4
ELM327 mode - can't connect to 2007 Chrysler & Country
« on: February 22, 2022, 23:52:48 »
My CANtieCAR won't connect to my 2007 Chrysler Town & Country in ELM327 mode. I'm using the "Car Scanner" Android app.
I believe the Town & Country uses J1850 VPW. I can connect to my 1997 F150 just fine, which uses J1850 PWM.
A cheap handheld OBD reader connects to my Town & Country without any issues.

Oleksandr

  • Administrator
  • Full Member
  • *****
  • Posts: 158
    • tieCAR.net Forum ::.
Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Reply #1 on: April 25, 2022, 15:14:06 »
we have not enough cars for SAE J1850VPW testings...
so the protocol is not ready

ViktorsS

  • Newbie
  • *
  • Posts: 2
Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Reply #2 on: May 22, 2022, 07:27:11 »
What is the best diagnostic and car configuring software for chrysler, for using on pc?

Oleksandr

  • Administrator
  • Full Member
  • *****
  • Posts: 158
    • tieCAR.net Forum ::.
Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Reply #3 on: August 20, 2022, 10:47:05 »
perhaps that is wiTech

Tune EMS

  • Newbie
  • *
  • Posts: 6
Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Reply #4 on: August 19, 2023, 01:43:37 »
we have not enough cars for SAE J1850VPW testings...
so the protocol is not ready

What does it take to set it up for J1850 VPW?

Oleksandr

  • Administrator
  • Full Member
  • *****
  • Posts: 158
    • tieCAR.net Forum ::.
Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Reply #5 on: September 04, 2023, 12:49:16 »
we have not enough cars for SAE J1850VPW testings...
so the protocol is not ready

What does it take to set it up for J1850 VPW?

We have to finish the protocol in firmware.
Are you the car owner or you need to support the protocol for your job?

Oleksandr

  • Administrator
  • Full Member
  • *****
  • Posts: 158
    • tieCAR.net Forum ::.
Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Reply #6 on: September 22, 2023, 13:35:33 »
SAE J1850 Protocol is fully supported in CANtieCAR v4.x and CANtieCAR v5.x with Normal and High Speed
- SAE J1850PWM: 41.6 Kbps and 83.3 Kbps
- SAE J1850VPW: 10.4 Kbps and 41.6 Kbps

Welcome to test
===
CANtieCAR v4.x support page
CANtieCAR v5.x support page

Tune EMS

  • Newbie
  • *
  • Posts: 6
Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Reply #7 on: September 23, 2023, 14:09:37 »
will this eventually be available for V3?

Oleksandr

  • Administrator
  • Full Member
  • *****
  • Posts: 158
    • tieCAR.net Forum ::.
Re: ELM327 mode - can't connect to 2007 Chrysler & Country
« Reply #8 on: September 24, 2023, 19:16:58 »
will this eventually be available for V3?


No