Recent posts

#1

CANtieCAR / Re: CANtieCAR Wi-Fi Native Sup...

Last post by Oleksandr - December 01, 2025, 11:04:09

Hi
Can you tell that i can forward CTC j2534 to internet for remote jobs ?

you can if you have public IP on your router
you can use VPN or port forwarding

Tried conected two laptops with vpn and dont found it

i am not sure about your network configuration
perhaps you have routing problem
try manual adding of CANtieCAR IP address on Network tab

#2

CANtieCAR / Re: CANtieCAR Wi-Fi Native Sup...

Last post by pardul - November 16, 2025, 16:47:55

Hi
Can you tell that i can forward CTC j2534 to internet for remote jobs ?
Tried conected two laptops with vpn and dont found it

#3

CANtieCAR / Re: CANtieCAR Wi-Fi Native Sup...

Last post by Oleksandr - June 15, 2025, 11:54:04

0 - Find CANtieCAR on port with USB connection
1 – Switch Wireless to WiFi on the System tab
2 – Configure WiFi on the WiFi tab
3 – Power the adapter only via the OBDII connector
4 – Connect to the CANtieCAR WiFi access point, if you have not registered the WiFi Station connection of CANtieCAR to your router, etc.
5 – Find CANtieCAR on the Network tab or add it manually, save the changes – this network port will be available on the Settings tab
6 – Find CANtieCAR on the network port in the Settings tab
7 – The Passthru driver will also search for CANtieCAR on the network... (actually the search is performed on all the last 10 ports where the configurator found CANtieCAR)

#4

Genuine / Re: AVT-852

Last post by Tune EMS - October 20, 2024, 22:59:02

yeah i brought a avt853 and like a few other people we had a hard time getting the vpw1850 to work, the can bus worked fine, just not the older protocal

#5

BMW / Re: tieCar adapter instead of ...

Last post by andrii - June 02, 2024, 10:34:39

I hope the developer can explain how it works. Please.

#6

BMW / Re: tieCar adapter instead of ...

Last post by pupu14 - June 01, 2024, 16:09:58

Sorry, no experience with bench setups..

#7

BMW / Re: tieCar adapter instead of ...

Last post by andrii - May 31, 2024, 17:59:32

Thank you for your answer.
But if it possible to use passthru and emulation kl15 in the same time?
At this moment i use cantie adapter as a source of "ignition" and icom as a diagnostic interface for working with bmw ecu ( headlights modules) on the table.
I suppose that it is possible to perform both the tasks using only cartie adapter.
What do you think about it?
Thank you

#8

BMW / Re: tieCar adapter instead of ...

Last post by pupu14 - May 30, 2024, 16:39:07

Hello,

Install BMW Passthru driver. MUST be v 2.1.0.0 - other ones does not work so well (or at all).
There are plenty of guides on the internet on this topic - just search "ISTA passthru driver".
Then, must choose Ediabas option in ISTA connection settings.

ISTA-P (cracked, with a launcher) will not work, only ISTA-D.

#9

BMW / tieCar adapter instead of ICOM

Last post by andrii - May 30, 2024, 07:03:55

Hello, everyone.
I`m sorry for maybe stupid question - is there a way to use tieCar adapter with ISTA instead of OEM ICOM?
If yes - could you, please, advice which settings needed?
As i know, the ICOM uses an IP address.
Thank you.

#10

CANtieCAR / Re: CANtieCAR Wi-Fi Native Sup...

Last post by pardul - March 15, 2024, 07:55:33

It was easy
when ctc was conected to acces point, just must search it in network tab in configurator and then it works